VPN (Virtual Private Network) is a technology that provides a secure tunnel across a public network. A private network user can send and receive data to any remote private network using VPN Tunnel as if his/her network device was directly connected to that private network.

MikroTik provides EoIP (Ethernet over IP) tunnel that is used to create a site to site VPN. EoIP tunneling is a MikroTik RouterOS protocol that creates an Ethernet tunnel between two MikroTik Routers on top of an IP connection. EoIP adds an outer header mentioning the entry point of the tunnel (SourceIP) and the exit point of the tunnel (DestinationIP) but the inner packet is kept unmodified.

EoIP tunnel only encapsulates IP packets but does not provide authentication and encryption. EoIP tunnel with IPsec ensures IP packet encapsulation as well as authentication and encryption. IPsec usage makes your packets secure but it works slowly because of having extra authentication and encryption process. So, my opinion is that if data security is your concern, use EoIP tunnel with IPsec but if data security is not so headache, use only MikroTik EoIP tunnel because it works so faster.

The goal of this article is to design an EoIP VPN tunnel with IPsec. So, in this article I will show how to create an EoIP tunnel with IPsec to establish a secure site to site VPN tunnel between two MikroTik Routers.

Network Diagram

To configure a site to site EoIP VPN Tunnel (with IPsec) between two MikroTik Routers, I am following a network diagram like below image.

In this network, Office1 Router is connected to internet through ether1 interface having IP address 192.168.70.2/30. In your real network this IP address will be replaced with public IP address provided by your ISP. Office1 Router’s ether2 interface is connected to local network having IP network 10.10.11.0/24. After EoIP tunnel configuration, an EoIP tunnel interface will be created in Office 1 Router whose IP address will be assigned 172.22.22.1/30.

Similarly, Office 2 Router is connected to internet through ether1 interface having IP address 192.168.80.2/30. In your real network this IP address will also be replaced with public IP address. Office 2 Router’s ether2 interface is connected to local network having IP network 10.10.12.0/24. After EoIP tunnel configuration an EoIP tunnel interface will also be created in Office 2 Router whose IP address will be assigned 172.22.22.2/30.

We will configure a site to site EoIP Tunnel between these two MikroTik Routers so that local network of these routers can communicate with each other through this VPN tunnel across public network.

Core Devices and IP Information

To configure a site to site EoIP VPN between two Routers, I am using two MikroTik RouterOS v6.38.1. IP information that I am using for this network configuration are given below.

• Office 1 Router WAN IP: 192.168.70.2/30, LAN IP Block 10.10.11.0/24 and Tunnel interface IP 172.22.22.1/30
• Office 2 Router WAN IP: 192.168.80.2/30, LAN IP Block 10.10.12.0/24 and Tunnel interface IP 172.22.22.2/30

This IP information is just for my RND purpose. Change this information according to your network requirements.

Site to Site EoIP Tunnel Configuration with IPsec

We will now start our site to site EoIP VPN configuration according to the above network diagram. Complete configuration can be divided into four parts.

• MikroTik RouterOS basic configuration
• EoIP tunnel configuration with IPsec
• Assigning IP address on tunnel interface
• Static route configuration

Part 1: MikroTik RouterOS Basic Configuration

Basic RouterOS configuration includes assigning WAN IP, LAN IP, DNS IP and Route, NAT configuration. According to our network diagram, we will now complete these topics in our two MikroTik RouterOS (Office 1 Router and Office 2 Router).

Office 1 Router Basic Configuration

The following steps will guide you how to perform basic configuration in your Office 1 RouterOS.

• Login to Office 1 RouterOS using winbox and go to IP > Addresses. In Address List window, click on PLUS SIGN (+). In New Address window, put WAN IP address (192.168.70.2/30) in Address input field and choose WAN interface (ether1) from Interface dropdown menu and click on Apply and OK button. Click on PLUS SIGN again and put LAN IP (10.10.11.1/24) in Address input field and choose LAN interface (ether2) from Interface dropdown menu and click on Apply and OK button.
• Go to IP > DNS and put DNS servers IP (8.8.8.8 or 8.8.4.4) in Servers input field and click on Apply and OK button.
• Go to IP > Firewall and click on NAT tab and then click on PLUS SIGN (+). Under General tab, choose srcnat from Chain dropdown menu and click on Action tab and then choose masquerade from Action dropdown menu. Click on Apply and OK button.
• Go to IP > Routes and click on PLUS SIGN (+). In New Route window, click on Gateway input field and put WAN Gateway address (192.168.70.1) in Gateway input field and click on Apply and OK button.

Basic RouterOS configuration has been completed in Office 1 Router. Now we will do similar steps in Office 2 RouterOS.

Office 2 Router Basic Configuration

The following steps will guide you how to perform basic configuration in your Office 2 RouterOS.

• Login to Office 2 RouterOS using winbox and go to IP > Addresses. In Address List window, click on PLUS SIGN (+). In New Address window, put WAN IP address (192.168.80.2/30) in Address input field and choose WAN interface (ether1) from Interface dropdown menu and click on Apply and OK button. Click on PLUS SIGN again and put LAN IP (10.10.12.1/24) in Address input field and choose LAN interface (ether2) from Interface dropdown menu and click on Apply and OK button.
• Go to IP > DNS and put DNS servers IP (8.8.8.8 or 8.8.4.4) in Servers input field and click on Apply and OK button.
• Go to IP > Firewall and click on NAT tab and then click on PLUS SIGN (+). Under General tab, choose srcnat from Chain dropdown menu and click on Action tab and then choose masquerade from Action dropdown menu. Click on Apply and OK button.
• Go to IP > Routes and click on PLUS SIGN (+). In New Route window, click on Gateway input field and put WAN Gateway address (192.168.80.1) in Gateway input field and click on Apply and OK button.

Basic RouterOS configuration has been completed in Office 2 Router. Now we are going to start EoIP tunnel configuration.

Part 2: EoIP Tunnel Configuration with IPsec

After MikroTik Router basic configuration, we will now configure EoIP tunnel with IPsec in both MikroTik RouterOS. In EoIP tunnel configuration, we will specify local and remote IP address as well as shared secret for IPsec and Tunnel ID.

EoIP Tunnel Configuration in Office 1 Router

The following steps will show how to configure EoIP tunnel in your Office 1 Router.

• Click on Interfaces menu item from Winbox and click on EoIP Tunnel tab and then click on PLUS SIGN (+). New Interface window will appear.
• Put a meaningful EoIP tunnel interface name (eoip-tunnel-r1) in Name input field.
• Put Office 1 Router’s WAN IP address (192.168.70.2) in Local Address input field.
• Put Office 2 Router’s WAN IP address (192.168.80.2) in Remote Address input field.
• Put a unique ID (for example: 10) in Tunnel ID input field. This ID must be same in both routers.
• Put IPsec shared secret in IPsec Secret input field if your router supports IPsec and you wish to enable IPsec authentication and encryption. You should remember that this IPsec Secret must be same in both routers.
• Also uncheck Allow Fast Path checkbox if it is checked and you want to enable IPsec.
• Click Apply and OK button.
• You will find a new EoIP tunnel interface followed by your given name (eoip-tunnel-r1) has been created in Interface List window.

EoIP tunnel configuration in Office 1 Router has been completed. Now we will do the similar steps in our Office 2 Router to create EoIP tunnel interface.

EoIP Tunnel Configuration in Office 2 Router

The following steps will show how to configure EoIP tunnel in your Office 2 Router.

• Click on Interfaces menu item from Winbox and click on EoIP Tunnel tab and then click on PLUS SIGN (+). New Interface window will appear.
• Put a meaningful EoIP tunnel interface name (eoip-tunnel-r2) in Name input field.
• Put Office 2 Router’s WAN IP address (192.168.80.2) in Local Address input field.
• Put Office 1 Routers WAN IP address (192.168.70.2) in Remote Address input field.
• Put a unique ID (for example: 10) in Tunnel ID input field. This ID must be same in both routers.
• Put IPsec shared secret in IPsec Secret input field if your router supports IPsec and you wish to enable IPsec authentication and encryption. You should remember that this IPsec Secret must be same in both routers.
• Also uncheck Allow Fast Path checkbox if it is checked and you want to enable IPsec.
• Click Apply and OK button.
• You will find a new EoIP tunnel interface followed by your given name (eoip-tunnel-r2) has been created in Interface List window.

EoIP tunnel configuration in Office 2 Router has been completed. Now we will assign IP address in our newly created EoIP tunnel interface in our both RouterOS so that both router can communicate with each other through this VPN tunnel interface.

Part 3: Assigning IP Address in EoIP Tunnel Interface

After EoIP tunnel configuration, a new EoIP tunnel interface has been created in both routers. So, if we assign same block IP in both interfaces, the both router will be able to communicate with each other through this EoIP tunnel. In this part, we will now assign IP address in our newly created tunnel interface.

Assigning IP Address on Office 1 Router’s EoIP Tunnel Interface

The following steps will show how to assign IP address on Office 1 Router’s tunnel interface.

• Go to IP > Address menu item and click on PLUS SIGN (+).
• Put a new private IP Block IP (172.22.22.1/30) in Address input field.
• Choose newly created tunnel interface (eoip-tunnel-r1) from Interface drop down menu.
• Click Apply and OK button.

Assigning IP address on Office 1 Router’s tunnel interface has been completed. Similarly, we will now assign IP address on Office 2 Router’s tunnel interface.

Assigning IP Address on Office 2 Router’s EoIP Tunnel Interface

The following steps will show how to assign IP address in Office 2 Router’s tunnel interface.

• Go to IP > Address menu item and click on PLUS SIGN (+).
• Put a new private IP Block IP (172.22.22.2/30) in Address input field.
• Choose newly created tunnel interface (eoip-tunnel-r2) from Interface drop down menu.
• Click Apply and OK button.

Assigning IP address on Office 2 Router’s tunnel interface has been completed. In this stage both routers are now able to communicate with each other. But both routers’ LAN cannot communicate with each other without configuring static routing. So, in the next part we will configure static routing in our both Office Router.

Part 4: Static Route Configuration

We will now configure static route in our both Office Router so that each router’s LAN can communicate with each other through EoIP tunnel.

Static Route Configuration in Office 1 Router

The following steps will show how to configure static route in Office 1 Router.

• Go to IP > Routes and click on PLUS SIGN (+). New Route window will appear.
• In New Route window, put destination IP Block (10.10.12.0/24) in Dst. Address input field.
• Put the Gateway address (172.22.22.2) in Gateway input field.
• Click Apply and OK button.

Static route configuration in Office 1 Router has been completed. Now we will configure static route in Office 2 Router.

Static Route Configuration in Office 2 Router

The following steps will show how to configure static route in Office 2 Router.

• Go to IP > Routes and click on PLUS SIGN (+). New Route window will appear.
• In New Route window, put destination IP Block (10.10.11.0/24) in Dst. Address input field.
• Put the Gateway address (172.22.22.1) in Gateway input field.
• Click Apply and OK button.

Static route configuration in Office 2 Router has been completed. Now both router as well as its LAN can communicate with each other through EoIP tunnel across public network.

To check your configuration, do a ping request from any router or any local network machine to other local network machine. If everything is OK, your ping request will be success.

If you face any confusion to follow the above steps properly, follow my video about MikroTik Site to Site EoIP Tunnel with IPsec carefully. I hope it will reduce your any confusion.

EoIP VPN Tunnel Configuration with IPsec has been explained in this article. I hope you will be able to configure EoIP tunnel with IPsec between your two office routers. However, if you face any confusion to configure EoIP tunnel in your MikroTik Router, feel free to discuss in comment or contact me from Contact page. I will try my best to stay with you.