build a wireless repeater
Most Relevant Content
How to Use Old Router as Range Extender to Boost WiFi Signal
WiFi is a technology to turn wired internet into WiFi internet and used in every home and office. Wireless internet gives you the freedom to use the internet without sitting in a single place. It is also true that speed performance drop in Wi-fi due to weak signal or interference. Sometimes laying a physical wired connection in every room is not possible. So Wi-Fi range extender setup helps you to boost signal strength. Instead of buying a new range extender device use old wifi router as range extender mode to boost Wifi signal. The easy method to boost Wi-fi signal coverage without using a range extender device is make wifi router as repeater mode which will extend signal. This post will help you turn old router as a range extender mode to improve wireless signals in the low signal areas. Setup WiFi Router as Range extender Mode To use the router as repeater mode need to access the settings page. To access the router login page use default IP Address router or Make factory reset if forget IP address. Connect Router LAN port to Desktop or Laptop LAN port. Use Static IP Address of the same series in LAN settings [...]
- »
How to Buy a Good WiFi Router for Home or Office | October 12, 2021
You are here because you want to buy a WiFi Router and want to know how to buy a good WiFi Router for your home or office or business. A lot of wireless routers are nowadays available in the market. But before buying a WiFi Router, you should know which one is a good WiFi Router for your need based on some features and specifications of the router. We will now see some key points those should have well understand [...]
- »
CentOS 8 Networking Configuration Using Cockpit Web Console | January 11, 2021
The first task after completing CentOS 8 fresh installation is to configure its networking so that it can be accessed from other network devices. In my previous article, I discussed how to install CentOS 8 Graphical User Interface (GNOME Desktop) with step by step screenshots. If you are a new CentOS 8 user and have not yet installed CentOS 8 on your server machine, feel free to follow that article and install CentOS 8 GNOME Desktop according to the article. [...]
- »
LVM Management in CentOS/Red Hat 7 Linux | March 15, 2019
LVM (Logical Volume Manager) is the recommended partition method for CentOS/Red Hat 7 Linux. Specially, if we work on Mail Server, File Server, FTP Server, Web Proxy Server or any application where disk space changes frequently, the LVM partition is mandatory in this case. In my previous article, I discussed how to install CentOS 7.5 with LVM partitioning. If you are new here or CentOS 7 is not yet installed, I will suggest you to follow my previous article and [...]
- »
MikroTik Site to Site EoIP Tunnel with IPsec | March 21, 2018
VPN (Virtual Private Network) is a technology that provides a secure tunnel across a public network. A private network user can send and receive data to any remote private network using VPN Tunnel as if his/her network device was directly connected to that private network. MikroTik provides EoIP (Ethernet over IP) tunnel that is used to create a site to site VPN. EoIP tunneling is a MikroTik RouterOS protocol that creates an Ethernet tunnel between two MikroTik Routers on top [...]
- »
CentOS 7.5 Installation with GUI and LVM Partition | March 7, 2019
Red Hat/CentOS Linux is a popular server operating system. Specially who work on mail server, web server, web proxy server, ftp server and file server are so familiar with the Red Hat/CentOS Linux. In my previous article, I discussed how to install CentOS 7.5 Linux step by step with the standard partition. But if you want to work on mail server, web proxy server, ftp server, file server or any other application where disk space changes frequently, the standard partitioning [...]
- »
How to Separate MikroTik Hotspot and DHCP IP Pool | October 9, 2020
MikroTik default Hotspot Setup comes with a DHCP Server (which uses same IP Pool of Hotspot Server) to provide IP address and other network information to a connected device. Using this automatic IP address connected device can access Hotspot login page. After successfully login, a one to one NAT IP address is also assigned for the device and this process happens internally in Hotspot Server. User device cannot know this one to one NAT IP assigning. However, Hotspot Server actually [...]
- »
MikroTik VLAN and Bridge Configuration | September 19, 2017
VLAN and Bridge are two useful features in MikroTik Router. These two features are frequently used in any MikroTik network configuration. VLAN divides a physical interface into multiple logical interfaces. So, you can isolate your network into multiple logical networks on a physical interface. On other hand, MikroTik Bridge integrates multiple physical interfaces in a logical interface. So, you can extend your broadcast domain on multiple physical interfaces and can extend your popular services such as PPPoE or DHCP on [...]
- »
Managing Disk Partition with the parted Tool in CentOS 7 | March 2, 2019
As a system administrator, sometimes you may require to manage partitions of your CentOS/Red Hat Linux Operating System. Partition management is always a risky task. But there are some useful tools those are so helpful to manage CentOS/Red Hat Linux disk partition easily. In my previous article, I discussed how to manage CentOS/Red Hat 7 HDD partitions with the fdisk utility. The fdisk tool is only eligible to manage MBR partition table. But GPT partition table is now becoming more [...]
- »
PPPoE Server Configuration in MikroTik RouterOS 7 | December 2, 2023
MikroTik PPPoE is a client-server protocol and mostly used at the end ISP configuration where MikroTik RouterOS acts as a PPPoE Server and user’s WiFi Router acts as PPPoE client. MikroTik PPPoE Server can be used with MikroTik simple queue management. So, it helps to manage user’s bandwidth easily. People who are trying to do internet business should learn MikroTik PPPoE Server. Configuring PPPoE Server in MikroTik RouterOS 7 is so easy. If you have knowledge on basic RouterOS 7 [...]
More Similar Content
You May Also Like
