calculate network bandwidth

Most Relevant Content

  • Network Bandwidth and Throughput

    Bandwidth and Throughput are two important basic networking terms in computer network. If you wish to be an expert network administrator, you must have better understanding about these two networking terms. As a network user, you should also have better understanding about network bandwidth and throughput so that you can get maximum output from your network service provider. In this article, I will explain about network bandwidth and throughput from very beginning. I hope, this article will enrich your networking concept. What are Bandwidth and Throughput? Bandwidth In computer network, bandwidth is defined as the maximum number of bits that can flow through a network connection in a given period of time. The fundamental unit of network bandwidth is bits per second (bps). An ISP network connection that specified a bandwidth of 1Mbps means that in one second, maximum 100000 bits can be transferred across this connection. The term bandwidth is normally used in internet broadband subscription plan. Normally a higher bandwidth subscription plan will cost more than that of a lower bandwidth subscription plan. One thing to note is that even if you are subscribing a 1Mbps internet broadband plan, you may not get the full 1Mbps bandwidth when [...]

    READ MORE »

  • You May Also Like

  • »

    How to Use Old Router as Range Extender to Boost WiFi Signal |   October 7, 2019

    WiFi is a technology to turn wired internet into WiFi internet and used in every home and office. Wireless internet gives you the freedom to use the internet without sitting in a single place. It is also true that speed performance drop in Wi-fi due to weak signal or interference. Sometimes laying a physical wired connection in every room is not possible. So Wi-Fi range extender setup helps you to boost signal strength. Instead of buying a new range extender [...]

    READ MORE »

  • »

    Restrict Internet Access Based on MAC Address in MikroTik |   February 4, 2017

    MikroTik router has a lot of features by which a network administrator can design his network as he likes. As a network administrator, sometimes you may need to allow internet access some specific devices. If other devices try to access internet, they will be rejected by your router. For example, say, you have configured a simple network like below diagram. In this network, you have configured WAN, LAN, Gateway, DNS and NAT. Also you have created queue rules for limiting [...]

    READ MORE »

  • »

    MikroTik Hotspot Setup with Radius Server (User Manager) |   January 6, 2018

    Hotspot is one of the most popular services in MikroTik Router. It is popularly used in Hotel and Restaurant, Railway Station or Airport, School or University Campus and so on. Even ISP network and office network also use MikroTik Hotspot for authenticating network clients/users. Hotspot user can be managed with Hotspot’s local user database or with a Radius Server. Radius Server gives facility to manage Hotspot user’s bandwidth and accounting easily and centrally. So, Hotspot setup with Radius Server can [...]

    READ MORE »

  • »

    MikroTik Multiple SSID with Separate LAN and DHCP Server |   October 30, 2019

    One of the most amazing features of MikroTik Wireless Router is creating Multiple SSID (Virtual AP) on a physical wireless interface. So, creating a Guest WiFi AP with separate LAN block, SSID and DHCP Server is so easy using MikroTik WiFi AP Router. In the previous article, I discussed how to configure MikroTik WiFi Access Point on physical wireless interface with DHCP Server using hAP Lite (RB941-2nD) Wireless Router. In this article I will discuss how to configure a Virtual [...]

    READ MORE »

  • »

    WiFi Station Setup in MikroTik Wireless Router |   November 27, 2019

    MikroTik Wireless Router is capable of working as a WiFi Client.  So, if any ISP provides WiFi connection for their clients, MikroTik Wireless Router can be used to connect to that ISP SSID by configuring wireless station mode. MikroTik WiFi station mode finds available SSID and connects with permitted SSID.  This wireless connection can be used as wireless WAN connection and configuring LAN, multiple devices can get internet over this wireless WAN connection. In my previous article, I discussed how [...]

    READ MORE »

  • »

    MikroTik VLAN and Bridge Configuration |   September 19, 2017

    VLAN and Bridge are two useful features in MikroTik Router.  These two features are frequently used in any MikroTik network configuration. VLAN divides a physical interface into multiple logical interfaces. So, you can isolate your network into multiple logical networks on a physical interface. On other hand, MikroTik Bridge integrates multiple physical interfaces in a logical interface. So, you can extend your broadcast domain on multiple physical interfaces and can extend your popular services such as PPPoE or DHCP on [...]

    READ MORE »

  • »

    How to Assign Static IP Address in Windows OS |   September 16, 2015

    Communication between one computer to another computer or server is established with IP addresses. Without IP address no communication is possible in computer network. An Internet Protocol (IP) Address is a numerical value or label assigned to each electronic device (e.g., computer, smartphone and printer) which uses Internet Protocol for communication. IP can be assigned both dynamically and statically on a IP devices. Dynamic IP is assigned by a DHCP server. If a DHCP server is present in a network, [...]

    READ MORE »

  • »

    MikroTik VRRP Configuration with Load Sharing |   November 19, 2018

    MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]

    READ MORE »

  • »

    CentOS 7.5 Installation Step by Step with GUI (GNOME Desktop) |   August 15, 2018

    Linux is a free and open source operating system developed by Linus Torvalds on September 17, 1991. It is mainly used as server environment. A lot of Linux distributions are present today. Among them, Red Hat Linux is used as enterprise Linux. Red Hat is also known as Red Hat commercial Linux that means Red Hat is a paid service program. CentOS (Community Enterprise Operating System) is another Linux distribution that provides a free and open source, enterprise-class, community-supported server platform functionally compatible with [...]

    READ MORE »