mikrotik vlan routing
Most Relevant Content
MikroTik VLAN Routing Configuration with Manageable Switch
A VLAN (Virtual LAN) is a group of computers, servers, network printers and other network devices that behave as if they were connected to a single network. VLAN is a logical topology that divides a single broadcast domain into multiple broadcast domains. VLAN is a layer 2 method. So, a manageable switch is required to manage VLAN in your network and a router is required to route and control your inter-VLAN. VLAN increases network security and performance as well as improves IT efficiency. So, it will be a better plan to implement VLAN in your network. If you have or manage MikroTik Router and manageable switch, VLAN implementation in your network is not so difficult. In this article, I will show how to easily configure inter-VLAN routing with MikroTik Router and manageable switch. Core Devices and IP Information To configure a VLAN network and inter-VLAN routing, I am using a MikroTik RouterBoard 1100 AHX2 (RouterOS v6.38.1) and Level One (GEP-2450) manageable switch. IP information that I am using for VLAN network configuration are given below. WAN IP 192.168.30.2/30 and Gateway IP 192.168.30.1 LAN networks: 10.10.20.0/24, 10.10.30.0/24 and 10.10.40.0/24 DNS IP: 8.8.8.8 and 8.8.4.4 This IP information is just for my R&D purpose. [...]
- »
VLAN Routing Configuration between MikroTik RouterOS | September 27, 2018
VLAN (Virtual Local Area Network) is a logical topology that divides a single broadcast domain into multiple broadcast domains. It increases network security and performance as well as improves network efficiency. MikroTik VLAN routing configuration with manageable switch was discussed in previous article. Today we will learn how to configure VLAN between MikroTik RouterOS. This Router to router VLAN (layer3 VLAN) is useful when any ISP provide connection to one or more local ISPs who use MikroTik Router to maintain [...]
- »
Troubleshooting Common Issues with Security Cameras in MikroTik Networks | February 7, 2025
30 Seconds Summary When fixing security cameras on MikroTik networks, you might see issues like bad video quality, connections dropping, motion detection not working, and security weaknesses. These problems can happen because of not enough internet speed, network congestion, IP conflicts, old software, or weak security. To fix these, make sure you have enough internet speed, set up the IP settings correctly, give camera traffic priority, and update the software regularly. Also, protect the cameras with strong passwords and encryption. [...]
- »
MikroTik VLAN and Bridge Configuration | September 19, 2017
VLAN and Bridge are two useful features in MikroTik Router. These two features are frequently used in any MikroTik network configuration. VLAN divides a physical interface into multiple logical interfaces. So, you can isolate your network into multiple logical networks on a physical interface. On other hand, MikroTik Bridge integrates multiple physical interfaces in a logical interface. So, you can extend your broadcast domain on multiple physical interfaces and can extend your popular services such as PPPoE or DHCP on [...]
- »
MikroTik WiFi Frequency Band and Channel Width Explanation | January 10, 2020
MikroTik WiFi frequency, band and channel width tuning is an important task in any wireless network. If we fail to setup WiFi frequency and channel width parameter properly, we will notice a poor performance of wireless network. WiFi is aimed at use within unlicensed spectrum and the unlicensed spectrum that is usually used for WiFi is 2.4 GHz and 5 GHz band. 2.4 GHz and 5 GHz bands have multiple channels and these channels must be setup properly to get [...]
- »
MikroTik Unequal Dual WAN Load Balancing with Failover using ECMP | September 15, 2019
MikroTik Router is capable of doing Load Balancing with Failover over multiple gateways. Policy Based Routing, ECMP, PCC and NTH Load Balancing are the popular load balancing methods in MikroTik Router. Among these methods, ECMP is so easy to configure and provides almost 100% load balancing and link redundancy solution. In my previous article, I discussed how to configure Load Balancing and Link Redundancy using ECMP over two equal bandwidth gateways. ECMP method is also capable of doing load balancing [...]
- »
MikroTik Hardware Redundancy with VRRP | October 8, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
How to Prevent Simultaneous User Login in MikroTik Hotspot | November 10, 2020
MikroTik Hotspot is a user based internet access system. Most of the user authentication and authorization can be controlled with MikroTik Hotspot. But sometimes some users misuse user based authentication system. Misusing simultaneous login is one of them. Usually we provide one username and password for a user and we expect he/she will use this username and password from only one device at a time. But it is also possible to use same username and password in multiple devices at [...]
- »
WiFi Station Setup in MikroTik Wireless Router | November 27, 2019
MikroTik Wireless Router is capable of working as a WiFi Client. So, if any ISP provides WiFi connection for their clients, MikroTik Wireless Router can be used to connect to that ISP SSID by configuring wireless station mode. MikroTik WiFi station mode finds available SSID and connects with permitted SSID. This wireless connection can be used as wireless WAN connection and configuring LAN, multiple devices can get internet over this wireless WAN connection. In my previous article, I discussed how [...]
- »
How to Block MAC Address in MikroTik RouterOS 7 | July 11, 2024
MikroTik RouterOS 7 by default allows any MAC address to get internet connection through it. But we may need to block some MAC addresses sometimes. There are three methods to block MAC address in MikroTik RouterOS 7 – Blocking MAC Address using Bridge Filter Rule. Blocking MAC Address using Firewall Filter Rule and Blocking MAC Address from DHCP Lease. We can use any of these methods if we want to block MAC Address in MikroTik Router. In this article, we [...]
More Similar Content
You May Also Like
