use router as repeater without cable

Most Relevant Content

  • How to Use Old Router as Range Extender to Boost WiFi Signal

    WiFi is a technology to turn wired internet into WiFi internet and used in every home and office. Wireless internet gives you the freedom to use the internet without sitting in a single place. It is also true that speed performance drop in Wi-fi due to weak signal or interference. Sometimes laying a physical wired connection in every room is not possible. So Wi-Fi range extender setup helps you to boost signal strength. Instead of buying a new range extender device use old wifi router as range extender mode to boost Wifi signal. The easy method to boost Wi-fi signal coverage without using a range extender device is make wifi router as repeater mode which will extend signal. This post will help you turn old router as a range extender mode to improve wireless signals in the low signal areas. Setup WiFi Router as Range extender Mode To use the router as repeater mode need to access the settings page. To access the router login page use default IP Address router or Make factory reset if forget IP address. Connect Router LAN port to Desktop or Laptop LAN port. Use Static IP Address of the same series in LAN settings [...]

    READ MORE »

  • You May Also Like

  • »

    MikroTik Hardware Redundancy with VRRP |   October 8, 2018

    MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]

    READ MORE »

  • »

    MikroTik Load Balancing and Link Redundancy with PBR |   March 31, 2019

    In computer networking, the Load Balancing technique is used to send network traffic over multiple gateways. If you have multiple ISP connections available, you can use load balancing technique to establish a stable network. You may now ask, why will I use multiple ISP connections? What are the benefits to use multiple ISP connections in my network? For your satisfaction, the following points are some reasons to use load balancing technique in your network. No ISP can give you 100% [...]

    READ MORE »

  • »

    Red Hat/CentOS Network Configuration |   August 4, 2017

    Red Hat/CentOS network configuration or IP configuration is an important task to a Linux system administrator. After completing RedHat 7/ CentOS 7 fresh installation, you have to first configure your system network so that it can communicate to other network devices. In my previous article, I discussed how to install CentOS 7 core packages successfully on your physical machine. If you are a new CentOS 7 user and yet you have not installed CentOS on your machine, feel free to study [...]

    READ MORE »

  • »

    WireGuard Site to Site VPN Between MikroTik RouterOS 7 |   September 29, 2022

    WireGuard is a free, open source, secure and high-speed modern VPN solution. WireGuard is extremely easy to implement but utilizes state-of-the-art cryptography. WireGuard can be used as either Client-Server VPN technology or Site to Site VPN technology. From the RouterOS 7, MikroTik introduces WireGuard VPN as their native package. So, who are using RouterOS 7 can use WireGuard VPN and can implement both client-server and site to site VPN with WireGuard free VPN server. In my previous article, I discussed [...]

    READ MORE »

  • »

    MikroTik Hotspot Login by HTTP CHAP, HTTP PAP and HTTPS |   July 25, 2020

    MikroTik Hotspot uses various types of login methods. Among these login methods HTTP CHAP, HTTP PAP and HTTPS are basic and important login methods. So, a MikroTik system administrator should have proper understanding on Hotspot HTTP CHAP, HTTP PAP and HTTPS login methods. In my previous article I discussed how to configure MikroTik Hotspot using Winbox. In this article I will discuss how to use HTTP CHAP, HTTP PAP and HTTPS login methods properly in MikroTik Hotspot Server. MikroTik Hotspot [...]

    READ MORE »

  • »

    Ubuntu Server 20.04 Installation with LVM |   May 28, 2021

    Linux is a free and open source operating system developed by Linus Torvalds on September 17, 1991. It is mainly used as server environment. A lot of Linux distributions are present today. Among them, Ubuntu is one of the best stable Linux distributions. Ubuntu has both Desktop and Server distribution. Ubuntu Server is a high performance and stable enterprise Linux distribution and it can be easily used in production. Ubuntu Server has both community-support and well documentation. So, IT guys can use Ubuntu [...]

    READ MORE »

  • »

    Turn Computer into Wi-Fi Hotspot |   September 17, 2015

    Internet Connection Sharing is an awesome feature in windows operating system. Using this feature, you can turn your computer which has wireless network card integrated into Wi-Fi hotspot and share your internet connection with your friends or family members. Generally, each laptop has a wireless network card integrated by default. So, if you are a laptop user, you can turn your laptop into Wi-Fi hotspot so easily. If you are a Desktop user, you can also turn your desktop as [...]

    READ MORE »

  • »

    MikroTik PCC Load Balancing over Unequal Dual WAN Links |   June 12, 2018

    Hi, you are here means you are finding a Load Balancing and Link Redundancy solution with Unequal WAN links in your MikroTik Router. If so, it is your right place. In my previous article I discussed how to configure a Dual WAN Load Balancing and Link Redundancy network using PCC method but it was assumed that both WAN links have equal bandwidth. But in real situation, you may have unequal WAN links such as ISP1 may have 10MB bandwidth and [...]

    READ MORE »

  • »

    How to Create Free SSL/TLS Certificate with OpenSSL |   July 23, 2021

    SSL/TLS certificate is required to encrypt data sent over internet communication. Without encryption, the sent data can be hacked by the middle man attack. SSL/TLS certificate is usually a pair key, public key and private key, solution where data is encrypted with public key and decrypted with private key. In public communication, public key is required to be signed by a CA (certificate authority) but in private communication, there is no need to be signed by any CA. If we [...]

    READ MORE »