virtual router redundancy protocol
Most Relevant Content
MikroTik Hardware Redundancy with VRRP
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back again. In this article, I will discuss how to configure MikroTik VRRP to establish a high available internet network. Network Diagram To configure VRRP in MikroTik Router, I am following a network diagram like the below image. In this network, two MikroTik RouterOS (Master_RouterOS and Backup_RouterOS) are the member of a MikroTik VRRP. So, when both routers are up and running, network traffic will pass through Master_RouterOS. If Master_RouterOS fails to operate due to hardware failure or any cause, Backup_RouterOS will turn into Master Router and pass network traffic until the Master_RouterOS comes back again. When the Master_RouterOS recovers again, it turns into Master Router and Backup_RouterOS will turn into Back Router. So, a hardware redundancy network will be ensured [...]
- »
MikroTik VRRP Configuration with Load Sharing | November 19, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
MikroTik VRRP Configuration with DHCP Server | October 22, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high available internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
CentOS 8 Networking Configuration Using Cockpit Web Console | January 11, 2021
The first task after completing CentOS 8 fresh installation is to configure its networking so that it can be accessed from other network devices. In my previous article, I discussed how to install CentOS 8 Graphical User Interface (GNOME Desktop) with step by step screenshots. If you are a new CentOS 8 user and have not yet installed CentOS 8 on your server machine, feel free to follow that article and install CentOS 8 GNOME Desktop according to the article. [...]
- »
How to Assign Static IP Address in Windows OS | September 16, 2015
Communication between one computer to another computer or server is established with IP addresses. Without IP address no communication is possible in computer network. An Internet Protocol (IP) Address is a numerical value or label assigned to each electronic device (e.g., computer, smartphone and printer) which uses Internet Protocol for communication. IP can be assigned both dynamically and statically on a IP devices. Dynamic IP is assigned by a DHCP server. If a DHCP server is present in a network, [...]
- »
MikroTik HotSpot One to One NAT/Universal HotSpot NAT | September 27, 2020
MikroTik Hotspot is an awesome service that can be customized widely. When MikroTik Hotspot is enabled on an interface, it adds dynamic destination NAT rules which will redirect all HTTP and HTTPS requests from unauthorized users to the Hotspot authentication proxy. So, no user can get internet access in Hotspot network without authentication. MikroTik Hotspot also uses one to one NAT providing an IP address from selected IP Pool and this IP address handles user’s data and limitation. Sometimes we [...]
- »
User Management in Linux (Red Hat/CentOS) | September 28, 2017
User management is an important part of Linux (especially Red Hat Enterprise Linux) system administration. Linux users can be administrated using user or group administration GUI (Graphical User Interface) tool as well as through Red Hat/CentOS Linux command prompt. But I will always suggest you to do command line user administration as much as possible because in production GUI will not be provided always. Many people who are learning Linux administration do not know all features of user administration command [...]
- »
Ubuntu Server Set Static IP Address with Netplan | July 1, 2021
Ubuntu Server is one of the most popular open source sever operating systems. Ubuntu Server can be used in production without any hassle. In my previous article, I discussed how to install Ubuntu Server’s latest version (Ubuntu Server 20.04) with LVM. In this article, we are going to see how to assign static IP address in Ubuntu Server with Netplan network management tool. Netplan Since Ubuntu Server 17.10, Netplan is being used as the default network management tool instead of [...]
- »
Download YouTube Video with Firefox Add-ons | August 26, 2015
YouTube is the most popular video sharing website. Statistics shows that YouTube is the second popular website of the world. So, it is nothing to say that you are a YouTube fan like me. As a YouTube fan, sometimes you may need to download YouTube videos which you like. Although, you often get an extra bandwidth for YouTube video streaming from your ISP now a days so that you can watch your favorite YouTube video without any buffering. But it [...]
- »
MikroTik Router First Time Startup and Setup using WebFig | April 17, 2018
I guess, you have purchased a new MikroTik Router or installed a new MikroTik RouterOS on PC and you are searching How to Start MikroTik Router First Time and How to Complete Basic RouterOS Configuration using WebFig (Web Interface) for running a basic network. If these are your concern, don’t worry, in this article I will show how to startup your MikroTik Router first time and complete RouterOS basic configuration using WebFig web interface so easily. There are three methods [...]
More Similar Content
You May Also Like
