vrrp with local dhcp

Most Relevant Content

  • MikroTik VRRP Configuration with DHCP Server

    MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high available internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back again. In my previous article, I discussed how to configure MikroTik VRRP to establish a high available internet network. But most of the office network as well as ISP network use DHCP Server to assign their device IP automatically. So, in this article I will show how to configure MikroTik VRRP with active and backup DHCP Server. Network Diagram To configure VRRP network with MikroTik DHCP Server, I am following a network diagram like the below image. In this network, two MikroTik RouterOS (Master_RouterOS and Backup_RouterOS) are the member of a MikroTik VRRP. So, when both routers are up and running, network traffic will pass through Master_RouterOS. If Master_RouterOS fails to operate due to hardware failure or any other cause, [...]

    READ MORE »

  • You May Also Like

  • »

    Install MikroTik RouterOS on PC |   June 13, 2016

    MikroTik is a popular and mostly used router worldwide because of having a lot of networking functionalities and its cheap price. If we buy a MikroTik Routerboard (like MikroTik Routerboard 450G, MikroTik Routerboard 1100 AH etc.), we will find a machine where MikroTik RouterOS is prebuilt but the machine contains limited processing resources such as limited RAM and limited processor core. So, our network could be slow if you use a MikroTik RouterBoard for maintaining a large network. On the [...]

    READ MORE »

  • »

    MikroTik HotSpot One to One NAT/Universal HotSpot NAT |   September 27, 2020

    MikroTik Hotspot is an awesome service that can be customized widely. When MikroTik Hotspot is enabled on an interface, it adds dynamic destination NAT rules which will redirect all HTTP and HTTPS requests from unauthorized users to the Hotspot authentication proxy. So, no user can get internet access in Hotspot network without authentication. MikroTik Hotspot also uses one to one NAT providing an IP address from selected IP Pool and this IP address handles user’s data and limitation. Sometimes we [...]

    READ MORE »

  • »

    MikroTik Hardware Redundancy with VRRP |   October 8, 2018

    MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]

    READ MORE »

  • »

    Securing MikroTik Router with Port Knocking |   March 21, 2021

    MikroTik Port Knocking strategy helps to protect MikroTik Router from hackers and unauthorized access as well as enhances MikroTik RouterOS security.

    READ MORE »

  • »

    MikroTik Send Browsing Log to Remote Syslog Server |   August 18, 2019

    MikroTik RouterOS is capable of logging various system events as well as user browsing information. Logs can be saved in router’s memory (RAM), disk, file, sent by email or even sent to remote syslog server. Sometimes it may require saving user browsing log by the law. So, a syslog server is an essential part to any network. In this article, I will discuss how to configure MikroTik Router to keep user browsing log and send that log to remote syslog [...]

    READ MORE »

  • »

    How to Mount USB Device in CentOS 7 (NTFS and Linux FS) |   February 18, 2019

    USB Hard Disk Drive or USB Flash Drive (Pen drive) is a popular external device that can be used to backup data or transfer data from one device to other device. In GUI (Graphical User Interface) Operating System such as Window or GNOME Desktop in Linux can automatically mount USB device and can show data in it if the File System of that device is supported. But all users do not like or always do not have GUI mode of [...]

    READ MORE »

  • »

    MikroTik PPPoE Server with Radius User Authentication |   December 17, 2017

    MikroTik PPPoE Server is popularly used in ISP Companies. Almost all Local ISP Companies use PPPoE service to manage their client’s connection. So, PPPoE Server Configuration places an important role in MikroTik RouterOS. MikroTik PPPoE Server configuration with local user database has been discussed in my previous article that is enough to manage PPPoE users for a single RouterOS. But if you have more than one RouterOS in your network or you need to manage your users remotely and more [...]

    READ MORE »

  • »

    User Management in Linux (Red Hat/CentOS) |   September 28, 2017

    User management is an important part of Linux (especially Red Hat Enterprise Linux) system administration. Linux users can be administrated using user or group administration GUI (Graphical User Interface) tool as well as through Red Hat/CentOS Linux command prompt. But I will always suggest you to do command line user administration as much as possible because in production GUI will not be provided always. Many people who are learning Linux administration do not know all features of user administration command [...]

    READ MORE »

  • »

    MikroTik User Manager RADIUS Installation on RouterOS 7 |   July 5, 2022

    The User Manager is a MikroTik provided RADIUS Server packages. It can be used to manage users for small or medium level business. User Manger is not a default RouterOS packages. So, we have to install user manager as an extra package in RouterOS 7. RouterOS 7 has brought a massive change on User Manager package. The most important change is managing User Manager from Winbox while in RouterOS 6 the User Manager package can only be managed from Web [...]

    READ MORE »