CAPsMAN channel selection
Frequency overlapping makes network performance so poor. So, CAPsMAN channel configuration with proper planning is required to avoid frequency overlapping.
Most Relevant Content
CAPsMAN Channel Planning with Non-Overlapping Frequency
MikroTik CAPsMAN is an excellent application for managing multiple CAPs (Controlled Access Point) in a Wireless Network. But multiple APs create frequency overlapping issue if channels are not configured properly. Channel overlapping is required for smooth connection while roaming but there should not be frequency overlapping because frequency overlapping makes wireless performance so poor. In my previous article, I discussed MikroTik CAPsMAN basic configuration with default channel configuration. In this article, I will discuss how to configure CAPsMAN channel to avoid frequency overlapping. Non Overlapping Channels One of my previous articles on WiFi Frequency Band and Channel Width showed the available non overlapping channels in 2.4 GHz Band. There are five non overlapping channel sets on 20MHz channel width in 2.4 GHz frequency but globally 1, 6 and 11 channel set is usually used. The middle frequency of these channels is given in the following table: Channel Number Middle Frequency 1 2412 6 2437 11 2462 In a multi WiFi AP network, the coverage of WiFi AP must be overlap for smooth connection but frequency overlapping must be avoided. So, we have to plan properly for designing a multi WiFi AP network. A possible multi WiFi AP network where there [...]
- »
MikroTik WiFi Frequency Band and Channel Width Explanation | January 10, 2020
MikroTik WiFi frequency, band and channel width tuning is an important task in any wireless network. If we fail to setup WiFi frequency and channel width parameter properly, we will notice a poor performance of wireless network. WiFi is aimed at use within unlicensed spectrum and the unlicensed spectrum that is usually used for WiFi is 2.4 GHz and 5 GHz band. 2.4 GHz and 5 GHz bands have multiple channels and these channels must be setup properly to get [...]
- »
Red Hat/CentOS Network Configuration | August 4, 2017
Red Hat/CentOS network configuration or IP configuration is an important task to a Linux system administrator. After completing RedHat 7/ CentOS 7 fresh installation, you have to first configure your system network so that it can communicate to other network devices. In my previous article, I discussed how to install CentOS 7 core packages successfully on your physical machine. If you are a new CentOS 7 user and yet you have not installed CentOS on your machine, feel free to study [...]
- »
Install MikroTik RouterOS on PC | June 13, 2016
MikroTik is a popular and mostly used router worldwide because of having a lot of networking functionalities and its cheap price. If we buy a MikroTik Routerboard (like MikroTik Routerboard 450G, MikroTik Routerboard 1100 AH etc.), we will find a machine where MikroTik RouterOS is prebuilt but the machine contains limited processing resources such as limited RAM and limited processor core. So, our network could be slow if you use a MikroTik RouterBoard for maintaining a large network. On the [...]
- »
MikroTik Bandwidth Management using Simple Queue | September 3, 2015
MikroTik is one of the most popular routers in computer networking. It is said that no office or ISP company cannot go a single day without MikroTik Router. MikroTik Router is also a popular router to a network administrator because MikroTik Router is easily maintainable with graphical user interface software named winbox than other routers. A lot of services are available in MikroTik router to run a network smoothly. Among these services, Bandwidth Management Service is the most popular service in [...]
- »
MikroTik HotSpot One to One NAT/Universal HotSpot NAT | September 27, 2020
MikroTik Hotspot is an awesome service that can be customized widely. When MikroTik Hotspot is enabled on an interface, it adds dynamic destination NAT rules which will redirect all HTTP and HTTPS requests from unauthorized users to the Hotspot authentication proxy. So, no user can get internet access in Hotspot network without authentication. MikroTik Hotspot also uses one to one NAT providing an IP address from selected IP Pool and this IP address handles user’s data and limitation. Sometimes we [...]
- »
MikroTik OpenVPN Setup with Windows Client | April 2, 2018
VPN (Virtual Private Network) technology provides a secure and encrypted tunnel across a public network. So, a private network user can send and receive data to any remote private network through VPN tunnel as if his/her network device was directly connected to that private network. MikroTik OpenVPN Server provides a secure and encrypted tunnel across public network for transporting IP traffic using PPP. OpenVPN uses SSL Certificates. So, OpenVPN Tunnel is a trusted tunnel to send and receive data across [...]
- »
MikroTik Site to Site OpenVPN Server Setup (RouterOS Client) | April 9, 2018
VPN (Virtual Private Network) technology provides a secure and encrypted tunnel across a public network. So, a private network user can send and receive data to any remote private network through VPN tunnel as if his/her network device was directly connected to that private network. MikroTik OpenVPN Server provides a secure and encrypted tunnel across public network for transporting IP traffic using PPP. OpenVPN Server uses SSL Certificates. So, OpenVPN Tunnel is a trusted tunnel to send and receive data [...]
- »
How to Assign Static IP Address in Windows OS | September 16, 2015
Communication between one computer to another computer or server is established with IP addresses. Without IP address no communication is possible in computer network. An Internet Protocol (IP) Address is a numerical value or label assigned to each electronic device (e.g., computer, smartphone and printer) which uses Internet Protocol for communication. IP can be assigned both dynamically and statically on a IP devices. Dynamic IP is assigned by a DHCP server. If a DHCP server is present in a network, [...]
- »
MikroTik Router Static DHCP Server Configuration | October 25, 2015
DHCP Server assigns IP address and other related IP information (Subnet mask, Gateway and DNS) automatically to network devices. But automatic DHCP Server has some disadvantages too. If any IP device connects to any automatic DHCP network, the device will get an IP address and related IP information automatically by the DHCP Server and the device will start to use resources of this network. In this situation, the network administrator cannot know who is being connected to the network and [...]
More Similar Content
You May Also Like
