increase wifi signal
Most Relevant Content
How to Use Old Router as Range Extender to Boost WiFi Signal
WiFi is a technology to turn wired internet into WiFi internet and used in every home and office. Wireless internet gives you the freedom to use the internet without sitting in a single place. It is also true that speed performance drop in Wi-fi due to weak signal or interference. Sometimes laying a physical wired connection in every room is not possible. So Wi-Fi range extender setup helps you to boost signal strength. Instead of buying a new range extender device use old wifi router as range extender mode to boost Wifi signal. The easy method to boost Wi-fi signal coverage without using a range extender device is make wifi router as repeater mode which will extend signal. This post will help you turn old router as a range extender mode to improve wireless signals in the low signal areas. Setup WiFi Router as Range extender Mode To use the router as repeater mode need to access the settings page. To access the router login page use default IP Address router or Make factory reset if forget IP address. Connect Router LAN port to Desktop or Laptop LAN port. Use Static IP Address of the same series in LAN settings [...]
- »
MikroTik WiFi Frequency Band and Channel Width Explanation | January 10, 2020
MikroTik WiFi frequency, band and channel width tuning is an important task in any wireless network. If we fail to setup WiFi frequency and channel width parameter properly, we will notice a poor performance of wireless network. WiFi is aimed at use within unlicensed spectrum and the unlicensed spectrum that is usually used for WiFi is 2.4 GHz and 5 GHz band. 2.4 GHz and 5 GHz bands have multiple channels and these channels must be setup properly to get [...]
- »
MikroTik VRRP Configuration with Load Sharing | November 19, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
MikroTik User Manager Installation and Basic Configuration | December 15, 2019
MikroTik User Manager is a RADIUS application developed by MikroTik team and can be used without charge. User Manager is used for authentication, authorization and accounting of MikroTik RouterOS, PPPoE, Hotspot, DHCP and Wireless users. Although User Manager Package is developed by MikroTik it will not be found in RouterOS by default. So, we have to install User Manager Package manually if we wish to use this RADIUS application. User Manager can be installed on MikroTik RouterBOARD, MikroTik CHR or [...]
- »
MikroTik Load Balancing with 2 PPPoE and 1 Static WAN using ECMP | September 24, 2019
ECMP provides almost 100% reliable load balancing and link redundancy solution. ECMP is a per connection load balancing where connection is marked with source and destination IP pair. In my previous article I discussed how to configure DUAL WAN load balancing with failover using ECMP method where WAN connections were static IP Addresses. But some ISP companies use PPPoE service for their client connection. So, some network administrators become confused to configure load balancing with PPPoE WAN connection because PPPoE [...]
- »
MikroTik Blocking All Websites Except a Few Websites | May 7, 2019
A few days ago, someone asked me how to block all websites except one with MikroTik Firewall. For this, I have decided to discuss about blocking all websites except someone’s whitelist. Unlike firewall devices, MikroTik Firewall by default allows all websites. So, if you need to block any website, you have to create a firewall rule that will block the specific website. Now if we want to block all websites and want to allow a few websites, we have to [...]
- »
Create System Restore Point in Windows OS | August 27, 2015
System Restore utility in windows operating system helps a windows user to take one or more snapshots of his/her windows system when windows operating system is working well. If any system crash occurs in future due to virus attack or critical system update or any unwanted program, the system can be reverted to its previous snapshot when windows OS was working well. So, System Restore utility in windows operating system is a very helpful service for windows users to protect [...]
- »
MikroTik Hotspot Configuration in RouterOS 7 | April 25, 2023
MikroTik Hotspot is an awesome service to run a captive portal network. You can run a public Wi-Fi network, Hotel Network, Airport network, CAMP Wi-Fi network, Shopping Mall Network and so on using MikroTik Hotspot and even can monetize your network for earning if you use Hotspot Billing Software like GalaxyRAD which is specially designed for MikroTik Hotspot network. GalaxyRAD helps to monetize your any network providing online payment gateway as well as integrating voucher-based system. It also helps to [...]
- »
How to Import SSL Certificate in MikroTik RouterOS | January 16, 2022
SSL/TLS Certificate is used to make secure communication between server and clients. MikroTik RouterOS has a lot of services such OVPN, SSTP VPN, HTTPS, Hotspot and so on those use SSL/TLS certificate. It is possible to create self-signed certificate in MikroTik RouterOS but self-signed certificate faces untrusted CA warning. So, it is always better to use trusted CA either freemium or premium. In my previous article, I discussed how to get a free SSL/TLS certificate from Zero SSL but Zero [...]
- »
MikroTik Unequal Dual WAN Load Balancing with Failover using ECMP | September 15, 2019
MikroTik Router is capable of doing Load Balancing with Failover over multiple gateways. Policy Based Routing, ECMP, PCC and NTH Load Balancing are the popular load balancing methods in MikroTik Router. Among these methods, ECMP is so easy to configure and provides almost 100% load balancing and link redundancy solution. In my previous article, I discussed how to configure Load Balancing and Link Redundancy using ECMP over two equal bandwidth gateways. ECMP method is also capable of doing load balancing [...]
More Similar Content
You May Also Like
