mikrotik vrrp with dhcp server
Most Relevant Content
MikroTik VRRP Configuration with DHCP Server
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high available internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back again. In my previous article, I discussed how to configure MikroTik VRRP to establish a high available internet network. But most of the office network as well as ISP network use DHCP Server to assign their device IP automatically. So, in this article I will show how to configure MikroTik VRRP with active and backup DHCP Server. Network Diagram To configure VRRP network with MikroTik DHCP Server, I am following a network diagram like the below image. In this network, two MikroTik RouterOS (Master_RouterOS and Backup_RouterOS) are the member of a MikroTik VRRP. So, when both routers are up and running, network traffic will pass through Master_RouterOS. If Master_RouterOS fails to operate due to hardware failure or any other cause, [...]
- »
MikroTik Hotspot Configuration with ECMP Load Balancing | September 4, 2021
MikroTik Hotspot is one of the most popular services in MikroTik RouterOS and day be day the demand of Hotspot service is increasing. MikroTik Hotspot can be used in any Airport, Hotel, Restaurant, Campus, Camp, Office or any ISP network. It is also possible to establish a WiFi Broadband Network with the MikroTik Hotspot service. How to configure MikroTik Hotspot was discussed in one of my previous articles. Although MikroTik Hotspot configuration is not so difficult but sometimes we face [...]
- »
Network Bandwidth and Throughput | February 17, 2017
Bandwidth and Throughput are two important basic networking terms in computer network. If you wish to be an expert network administrator, you must have better understanding about these two networking terms. As a network user, you should also have better understanding about network bandwidth and throughput so that you can get maximum output from your network service provider. In this article, I will explain about network bandwidth and throughput from very beginning. I hope, this article will enrich your networking [...]
- »
FreeRADIUS MySQL Database GUI with phpMyAdmin on CentOS 7 | January 30, 2019
FreeRADIUS is a high performance RADIUS Server that accepts a large number of networking devices as RADIUS Client including MikroTik Router. MySQL is one of the best user sources for freeRADIUS server. In my previous article, I discussed how to install freeRADIUS server on CentOS 7 and how to integrate MySQL module with freeRADIUS server. I also discussed how to create user group and profile in MySQL database server and authenticate MikroTik PPPoE client with MySQL database user. I used [...]
- »
Restrict Internet Access Based on MAC Address in MikroTik | February 4, 2017
MikroTik router has a lot of features by which a network administrator can design his network as he likes. As a network administrator, sometimes you may need to allow internet access some specific devices. If other devices try to access internet, they will be rejected by your router. For example, say, you have configured a simple network like below diagram. In this network, you have configured WAN, LAN, Gateway, DNS and NAT. Also you have created queue rules for limiting [...]
- »
VMware ESXi 6.7 Installation and Basic Configuration | November 17, 2020
VMware vSphere is the pioneer in virtualization. No other virtualization software is as feature rich as VMware vSphere. More than 500,000 enterprise data center are now using VMware vSphere. It is expected that most of the data center will be turned into virtualization near future. As VMware vSphere provides more feature than any other virtualization software, it is also expected that demand of VMware vSphere will be increased day by day. VMware ESXi is the foundation of VMware vSphere and [...]
- »
How to Prevent Simultaneous User Login in MikroTik Hotspot | November 10, 2020
MikroTik Hotspot is a user based internet access system. Most of the user authentication and authorization can be controlled with MikroTik Hotspot. But sometimes some users misuse user based authentication system. Misusing simultaneous login is one of them. Usually we provide one username and password for a user and we expect he/she will use this username and password from only one device at a time. But it is also possible to use same username and password in multiple devices at [...]
- »
Ubuntu Server Set Static IP Address with Netplan | July 1, 2021
Ubuntu Server is one of the most popular open source sever operating systems. Ubuntu Server can be used in production without any hassle. In my previous article, I discussed how to install Ubuntu Server’s latest version (Ubuntu Server 20.04) with LVM. In this article, we are going to see how to assign static IP address in Ubuntu Server with Netplan network management tool. Netplan Since Ubuntu Server 17.10, Netplan is being used as the default network management tool instead of [...]
- »
How to Bind Hotspot User to MAC and Static IP in MikroTik | November 6, 2020
MikroTik Hotspot is usually a user based Hotspot access controlling system. Internet access and bandwidth can easily be maintained with Hotspot user based system. But sometimes we may require more control on Hotspot system which is not possible only username based system. So, we may need to bind hotspot user to MAC and static IP address. If we can bind hotspot user to static IP address, it is easy to control Hotspot users with MikroTik Router and Firewall. So, in [...]
- »
How to Add New Domains to BIND DNS Server | July 5, 2019
DNS (Domain Name System) Server is an essential part to any computer network. So, it is always suggest keeping a DNS Server in every network. How to configure a DNS Server with BIND package was discussed in my previous article. A common question among the fresher admins of BIND DNS is how to add a new domain to BIND DNS Server. For this, this article is designed to discuss the proper way to add multiple domains to BIND DNS Server. [...]
You May Also Like
