MikroTik WiFi Frequency and Channel Width
Most Relevant Content
MikroTik WiFi Frequency Band and Channel Width Explanation
MikroTik WiFi frequency, band and channel width tuning is an important task in any wireless network. If we fail to setup WiFi frequency and channel width parameter properly, we will notice a poor performance of wireless network. WiFi is aimed at use within unlicensed spectrum and the unlicensed spectrum that is usually used for WiFi is 2.4 GHz and 5 GHz band. 2.4 GHz and 5 GHz bands have multiple channels and these channels must be setup properly to get high wireless performance. In my previous article I discussed how to setup MikroTik Wireless Router as a WiFi AP and in this article I will discuss how to setup frequency, band and channel width to get high wireless performance. IEEE 802.11 Standards and Frequency Band IEEE 802.11 specifies protocols for implementing Wireless Local Area Network (WLAN) WiFi computer communication in various frequencies including 2.4 GHz and 5 GHz band. IEEE 802.11 has several different variants those use different frequency band. The following table is a summarization of bands used by 802.11 systems. IEEE 802.11 VARIANT FREQUENCY BANDS USED 802.11a 5GHz 802.11b 2.4GHz 802.11g 2.4GHz 802.11n 2.4 & 5 GHz 802.11ac Below 6GHz 802.11ad Up to 60 GHz 802.11af [...]
- »
CAPsMAN Channel Planning with Non-Overlapping Frequency | March 16, 2020
MikroTik CAPsMAN is an excellent application for managing multiple CAPs (Controlled Access Point) in a Wireless Network. But multiple APs create frequency overlapping issue if channels are not configured properly. Channel overlapping is required for smooth connection while roaming but there should not be frequency overlapping because frequency overlapping makes wireless performance so poor. In my previous article, I discussed MikroTik CAPsMAN basic configuration with default channel configuration. In this article, I will discuss how to configure CAPsMAN channel to [...]
- »
ISP Bandwidth Management with MikroTik PCQ | June 25, 2016
MikroTik is an excellent router for managing ISP or local ISP Bandwidth. For this, most of the ISPs are now using MikroTik router for managing their client bandwidth. There are various types of queue services in MikroTik router for managing internet bandwidth. Among them PCQ can specially be used for maintaining ISP or local ISP bandwidth. So, in this article I will show how to maintain ISP or local ISP Bandwidth with MikroTik PCQ service. MikroTik PCQ Service PCQ stands [...]
- »
MikroTik User Management (RouterOS User) | October 22, 2017
MikroTik User Management plays an important role in MikroTik system administration as well as MikroTik security. Don’t be confused the title User Management with the MikroTik UserManager. UserManager is an optional and totally separate package distributed by MikroTik. UserManager is an implementation of Radius server that is used to maintain not only RouterOS users but also PPPoE, PPTP, Hotspot, Wireless and DHCP users. In my few future articles, I will discuss how to maintain these users with MikroTik UserManager Radius [...]
- »
Enable F8 Menu to Enter Safe Mode in Windows 8 & 10 | August 27, 2015
Windows is the most popular operating system in the world. No computer user can go a single day without windows operating system. As windows is a popular operating system, it has a lot of viruses also. But windows provides various tools for removing these viruses. For removing any unwanted program, windows safe mode is a best option. A popular way to open windows safe mode is windows Advanced Boot Options. Advanced Boot Options provides different run levels for windows users so [...]
- »
MikroTik VRRP Configuration with Load Sharing | November 19, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
MikroTik VLAN and Bridge Configuration | September 19, 2017
VLAN and Bridge are two useful features in MikroTik Router. These two features are frequently used in any MikroTik network configuration. VLAN divides a physical interface into multiple logical interfaces. So, you can isolate your network into multiple logical networks on a physical interface. On other hand, MikroTik Bridge integrates multiple physical interfaces in a logical interface. So, you can extend your broadcast domain on multiple physical interfaces and can extend your popular services such as PPPoE or DHCP on [...]
- »
MikroTik Hotspot Free Trial Internet Setup | August 14, 2020
MikroTik Hotspot is an awesome Hotspot internet solution. It has a lot of features to customize any Hotspot service. Sometimes we may require providing free trial internet in a Hotspot service. MikroTik Hotspot provides easy solution to provide free trial internet to the new user before going to paid version. In my previous article I discussed how to configure MikroTik Hotspot using Winbox. In this article I will discuss how to configure free trial internet in MikroTik Hotspot Server. Free [...]
- »
MikroTik VLAN Routing Configuration with Manageable Switch | July 11, 2018
A VLAN (Virtual LAN) is a group of computers, servers, network printers and other network devices that behave as if they were connected to a single network. VLAN is a logical topology that divides a single broadcast domain into multiple broadcast domains. VLAN is a layer 2 method. So, a manageable switch is required to manage VLAN in your network and a router is required to route and control your inter-VLAN. VLAN increases network security and performance as well as [...]
- »
MikroTik Dual WAN Load Balancing with Failover using PCC | May 27, 2018
Hi geek, going through this article means you are finding Load Balancing as well as Link Redundancy solution for your MikroTik network because you already have multiple WAN connections or you are planning to lease multiple WAN connections. MikroTik has various Load Balancing and Link Redundancy methods such as ECMP, PCC and so on. ECMP method provides an easy configurable load balancing with failover solution but it has some known issues too in a large network. On the hand, PCC [...]
More Similar Content
You May Also Like
