mikrotik vrrp configuration
Most Relevant Content
MikroTik Hardware Redundancy with VRRP
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back again. In this article, I will discuss how to configure MikroTik VRRP to establish a high available internet network. Network Diagram To configure VRRP in MikroTik Router, I am following a network diagram like the below image. In this network, two MikroTik RouterOS (Master_RouterOS and Backup_RouterOS) are the member of a MikroTik VRRP. So, when both routers are up and running, network traffic will pass through Master_RouterOS. If Master_RouterOS fails to operate due to hardware failure or any cause, Backup_RouterOS will turn into Master Router and pass network traffic until the Master_RouterOS comes back again. When the Master_RouterOS recovers again, it turns into Master Router and Backup_RouterOS will turn into Back Router. So, a hardware redundancy network will be ensured [...]
- »
MikroTik VRRP Configuration with Load Sharing | November 19, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high availability internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
MikroTik VRRP Configuration with DHCP Server | October 22, 2018
MikroTik VRRP (Virtual Router Redundancy Protocol) ensures high available internet network. If any organization requires uninterrupted internet connection, MikroTik VRRP implementation will be a vital solution for them. MikroTik VRRP creates a virtual router accumulating two or more physical routers and ensures uninterrupted internet connection keeping activate one physical router always. That means, if any physical router fails to operate due to any hardware failure, MikroTik VRRP uses another backup router for internet gateway until the running router comes back [...]
- »
CentOS 7 Partition Management with fdisk Utility | February 11, 2019
CentOS or Red Hat Linux is a popular server operating system to the system administrators. Almost all the system admins or IT guys who play with mail server, file server, proxy server and so on are so known with CentOS or Red Hat Linux and cannot go a single day without this operating system. The guys who are also wish to be a system admin should be familiar with CentOS or Red Hat operating system. In my previous article, I [...]
- »
MikroTik HotSpot One to One NAT/Universal HotSpot NAT | September 27, 2020
MikroTik Hotspot is an awesome service that can be customized widely. When MikroTik Hotspot is enabled on an interface, it adds dynamic destination NAT rules which will redirect all HTTP and HTTPS requests from unauthorized users to the Hotspot authentication proxy. So, no user can get internet access in Hotspot network without authentication. MikroTik Hotspot also uses one to one NAT providing an IP address from selected IP Pool and this IP address handles user’s data and limitation. Sometimes we [...]
- »
Restrict Internet Access Based on MAC Address in MikroTik | February 4, 2017
MikroTik router has a lot of features by which a network administrator can design his network as he likes. As a network administrator, sometimes you may need to allow internet access some specific devices. If other devices try to access internet, they will be rejected by your router. For example, say, you have configured a simple network like below diagram. In this network, you have configured WAN, LAN, Gateway, DNS and NAT. Also you have created queue rules for limiting [...]
- »
CentOS 8 Networking Configuration Using Cockpit Web Console | January 11, 2021
The first task after completing CentOS 8 fresh installation is to configure its networking so that it can be accessed from other network devices. In my previous article, I discussed how to install CentOS 8 Graphical User Interface (GNOME Desktop) with step by step screenshots. If you are a new CentOS 8 user and have not yet installed CentOS 8 on your server machine, feel free to follow that article and install CentOS 8 GNOME Desktop according to the article. [...]
- »
Ubuntu Server 20.04 Installation with LVM | May 28, 2021
Linux is a free and open source operating system developed by Linus Torvalds on September 17, 1991. It is mainly used as server environment. A lot of Linux distributions are present today. Among them, Ubuntu is one of the best stable Linux distributions. Ubuntu has both Desktop and Server distribution. Ubuntu Server is a high performance and stable enterprise Linux distribution and it can be easily used in production. Ubuntu Server has both community-support and well documentation. So, IT guys can use Ubuntu [...]
- »
How to Assign Static IP Address in Windows OS | September 16, 2015
Communication between one computer to another computer or server is established with IP addresses. Without IP address no communication is possible in computer network. An Internet Protocol (IP) Address is a numerical value or label assigned to each electronic device (e.g., computer, smartphone and printer) which uses Internet Protocol for communication. IP can be assigned both dynamically and statically on a IP devices. Dynamic IP is assigned by a DHCP server. If a DHCP server is present in a network, [...]
- »
CentOS 7 Network Configuration Using nmtui Tool | August 27, 2018
After completing CentOS 7 fresh installation, the first task to a system administrator is to configure its network so that it can communicate to other network devices. In my previous article, I discussed how to install CentOS 7.5 GUI (GNOME Desktop) step by step. If you are a new CentOS 7 user and yet you have not installed CentOS 7.5 on your server machine, feel free to study my previous article and install CentOS 7.5 GNOME Desktop according to that [...]
More Similar Content
You May Also Like
